Welcome to our Marketplace!
Please contact us to purchase any of our products or to get more information and details!
Phone: (317) 858-7793
Email: sales@ipcindy.com
*Temporarily Unavailable*
3M Turbo Mixing Nozzles
-Mixing Ratio: 1:1, 2:1
-For Dispensing and Mixing Two-Component Epoxy
-Dual Manual, Square Design (Green)
*Temporarily Unavailable*
3M Applicator Gun
-Two part manual applicator gun
-Fiberglass
-Can be used with 3M’s 1:1 50ml and 2:1 37.5ml cartridges
*Temporarily Unavailable*
Description: Set contains one resin pump and two hardener pumps
300 Mini Pumps are designed for convenient and accurate metering of WEST SYSTEM 105 Resin-based epoxy.
-Contains 1 resin pump and 2 hardener pumps
-Pumps mount directly on the resin and hardener containers and eliminate the mess involved with measuring by weight or volume
-Pumps are calibrated to deliver the proper working ratio with: ONE full pump of resin for each ONE full pump of hardener
-Pumps are ready to install on the Group Size B containers
-Please read and follow the priming, ratio verification and operating instructions included with the pumps
NOTE: Prices are sold by the linear yard. Please call for availability and pricing.
2×2 Carbon Fiber Dry Woven Fabric
-3K 2×2 Till Weave
-50” Wide
-Dry – 3k/2×2/50in
*Temporarily Unavailable*
Name: 50” Wide Fiberglass Fabric
NOTE: Prices are sold by the linear yard. Please call for availability and pricing.
Description: Chopped Strand; 1.5oz/50in
Fiberglass, Chopped Strand
-1.5 oz Chopped Strand Mat
-50” Wide
NOTE: Prices are sold by the linear yard. Please call for availability and pricing.
P3 Perforated Release Film
-Low cost, high-temperature release film
-Flat film can be applied quickly and without wrinkles over simple tooling and part shapes
-Highly visible color reduces risk of leaving film on cured parts
-Maximum use temperature: 380F (193C)
-Please see attached data sheet for additional information/instruction
Name: Breather Cloth
NOTE: Prices are sold by the linear yard. Please call for availability and pricing.
Description: 60inch; 4oz
4 oz Breather Cloth, 60” wide
-Stretchable, 100% non-woven polyester fabric designed to allow airflow throughout the vacuum bagging process, as well as bleed out any excess resin in a composite part
-Highly efficient due to multi-directional stretch, combined with low density, lightweight construction
-Allows great conformity around a composite part while under vacuum
-No binders which could close off airflow or stick to other components
-Please see data sheet for additional information and usage instructions
NOTE: Prices are sold by the linear yard. Please call for availability and pricing.
60” V-Fold Vacuum Bag
-High temperature bagging film
-Maximum use temperature: 400° F (204°C)
-Maximum stretch capability: 450% of original length
-Please see data sheet for additional information and usage instructions
NOTE: Prices are sold by the linear yard. Please call for availability and pricing.
Peel Ply
-Heat set and scoured nylon peel ply
-Contains red tracers which make it more visible before and after a cure, reducing the possibility of the peel ply bing left on the part
-Eliminates or decreases the need for sanding or abrading on your composite laminate
-Maximum use temperature: 375 F(190C)
-Please see data sheet for additional information and usage instructions
*Temporarily Unavailable*
Part Number: DP420
3M Epoxy Adhesive
-High peel and shear strength
-Maintains lasting bond at high and low temperatures
-20 minute work life
-Adhesive cures at room temperature
-Reaches high strength quickly with heat cure
-Recommended Applications
= Small joint assembly
= Heavy-duty mounting assembly
= Metalworking
= Carbon fiber epoxy bonding
206 Slow Hardener is a low-viscosity epoxy curing agent for use when extended working time or a longer cure time is needed.
-Provides adequate working time at higher shop temperatures
-Mix with WEST SYSTEM 105 Resin in a 5-part Resin to 1-part hardener ratio
-Once cured, it forms a rigid, high-strength, moisture-resistant solid
-206 Slow Hardener is not intended for clear coating
-Pot Life at 72F (22C): 22 to 25 minutes
-Cure to a solid state: 10 to 15 hours
-Cure to maximum strength: 1 to 4 days
-Minimum recommended temperature: 60F (16C)
-.86 gallon
-Please see attached data sheet for additional information/instruction
Altek H800 Series Polyester Resin
-Designed for use in the manufacturing of composite parts using hand lay-up application methods
-Fast cure rate allows for faster production rates without loss of surface profil
-Reduced post cure
-Fast and complete fiber wet-out
-Adaptable to a variety of manufacturing processes and conditions
-Polyester ; $60/gal
-Please see attached data sheet for additional information/instruction
205 Fast Hardener is a medium-viscosity epoxy curing agent. It is useful in a majority of bonding situations, and at lower temperatures.
-Produces a rapid epoxy cure that develops physical properties quickly at room temperature
-Mix with WEST SYSTEM 105 Resin in a 5-part resin to 1-part hardener ratio
-Resulting cured epoxy is a rigid, high-strength, moisture resistant solid
-Pot Life at 72F (22C): 9 to 12 minutes
-Cures to a solid state: 6 to 8 hours
-Cures to maximum strength: 1 to 4 days
-Minimum recommended temperature: 40F (4C)
-.86 gallon
-Please see attached data sheet for additional information/instruction
Pricing: 105-B; .86 gal – $51.35, and .98 gal – $106.5
105 Epoxy Resin is the base material on which all WEST SYSTEM 105 System epoxy compounds are built.
-Clear, pale yellow, low-viscosity liquid epoxy resin
-Blended with hardener at the proper ratio, it cures to a hard, solid plastic with superior physical properties
-Based on which hardener you choose, it cures at a wide range of temperatures.
-Once cured, it forms a high-strength solid that is functionally waterproof, an highly resistant to moisture vapor.
-Safety Data Sheet: WS-SDS-Epoxy-Resin-105-B
Part Number: IPC-AO-xxx (reference table below for full part number)
Name: Reference table below for full name
Technical drawings:
IPC Part # | Part Description | Dim A Grip Length | Dim B | Dim C | Dim D | Dim E | Price |
IPC-AO-008 | DZUS Button | 0.425 | 0.405 | 0.680 | n/a | n/a | $1.75 |
IPC-AO-008B | DZUS Button – Black Anodized | 0.425 | 0.405 | 0.680 | n/a | n/a | $3.10 |
IPC-AO-008S | DZUS Spring 1.375 x .375 Gold | 1.375 | n/a | 0.375 | n/a | n/a | $0.72 |
IPC-AO-008-1” | DZUS Button – 1” | 0.425 | 0.405 | 1.000 | n/a | n/a | $1.95 |
IPC-AO-008-1”B | DZUS Button – 1” Black Anodized | 0.425 | 0.405 | 1.000 | n/a | n/a | $3.10 |
IPC-AO-009 | DZUS Button | 0.450 | 0.405 | 0.680 | n/a | n/a | $1.75 |
IPC-AO-009B | DZUS Button – Black Anodized | 0.450 | 0.405 | 0.680 | n/a | n/a | $3.10 |
IPC-AO-009-1” | DZUS Button – 1” | 0.450 | 0.405 | 1.000 | n/a | n/a | $1.95 |
IPC-AO-009-1”B | DZUS Button – 1” Black Anodized | 0.450 | 0.405 | 1.000 | n/a | n/a | $3.10 |
IPC-AO-010 | DZUS Button | 0.500 | 0.405 | 0.680 | n/a | n/a | $1.75 |
IPC-AO-010B | DZUS Button – Black Anodized | 0.500 | 0.405 | 0.680 | n/a | n/a | $3.10 |
IPC-AO-010-1” | DZUS Button – 1” | 0.500 | 0.405 | 1.000 | n/a | n/a | $1.95 |
IPC-AO-010-1”B | DZUS Button – 1” Black Anodized | 0.500 | 0.405 | 1.000 | n/a | n/a | $3.10 |
IPC-AO-011 | DZUS Button | 0.550 | 0.405 | 0.680 | n/a | n/a | $1.75 |
IPC-AO-012 | DZUS Button | 0.600 | 0.405 | 0.680 | n/a | n/a | $1.75 |
IPC-AO-012B | DZUS Button – Black Anodized | 0.600 | 0.405 | 0.680 | n/a | n/a | $3.10 |
IPC-AO-014Weld | DZUS Button – Wheel Cover (Weld) | 0.500 | 0.405 | 0.680 | 0.340 | 0.235 | $3.10 |
IPC-AO-015Sanders | DZUS Button – Wheel Cover (Sanders) | 0.600 | 0.405 | 0.680 | 0.340 | 0.235 | $3.10 |
Part Number: IPC-AO-041
Description: Note various sizes are available:
- 15.00 inches x 1.00 inches
- 15.00 inches x 1.25 inches
- 16.00 inches x 1.00 inches